|
|
|
Search NMEA 2000® Certified Products
Only the NMEA 2000® certified products (A-Z Listing) below have met all requirements and have full NMEA 2000® certification. Products that are marketed or labelled : "NMEA 2000 compliant" or "works with NMEA 2000" are not NMEA 2000® certified and may not interoperate properly with other NMEA 2000® certified products.
Make sure products you buy are NMEA 2000® Certified
|
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
|
|
|
|
|
Yacht Devices LTD
|
1001 W. Broadway, Suite 381
Pacific Business Centre, #101
Vancouver, BC BC V6H 4E4
Canada
|
|
www.yachtd.com
|
Manufacturer Code :
717
|
|
YDTC-13 Digital Thermometer
|
|
Model #:
YDTC -13
|
|
The Thermometer performs measurements within the range from -55 to +125°C (-67..+257°F), the sensor is placed outside the case on a flexible, 95cm wire in a sealed stainless steel sleeve and can be used to measure the temperature of gases or liquids. If necessary, the wire can be elongated up to 100 meters. The Thermometer can be configured by the user to display data as "Air temperature", "Sea temperature", "Temperature in the refrigerator", "Temperature in the engine room", "Bait Well Temperature", etc.
|
|
Software Version:
1.30
|
|
Hardware Version:
1.00
|
|
Date Certified:
11/28/2016
|
|
Load Equivalency Number:
1
|
|
|
|
Yacht Device Humidity Sensor
|
|
Model #:
YDHS-01
|
|
Yacht Device Humidity and air temperature digital sensor for NMEA 2000 marine networks. Can be configured by the user to display data as "Inside humidity / temperature" (cabin) or "Outside humidity / temperature".
|
|
Software Version:
1.0
|
|
Hardware Version:
1.0
|
|
Date Certified:
3/17/2017
|
|
Load Equivalency Number:
1
|
|
|
|
Engine Gateway
|
|
Model #:
YDEG-04
|
|
Yacht device's Gateway for Volvo Penta, BRP, Rotax and J1939 engines to NMEA 2000 marine electronics network. It will provide with engine revolutions, motor hours, coolant temperature, battery voltage, warning and alarms, fuel rate and other data on the screen of your chart plotter.
|
|
Software Version:
1.15
|
|
Hardware Version:
1.0
|
|
Date Certified:
7/14/2017
|
|
Load Equivalency Number:
1
|
|
|
|
Digital Barometer
|
|
Model #:
YDBC-05
|
|
Digital Yacht's Barometer is intended for measuring atmospheric pressure within the range from 300 to 1100 hPa (mbar). The sensor is located inside the device case. The Device dimensions, including the connector, are 54x20x20mm, the mass is only 11 grams. Pressure data output resolution 0.01 hPa (mbar), absolute measurement accuracy is ±1 hPa, relative measurement accuracy is ±0.12 hPa.
|
|
Software Version:
1.40
|
|
Hardware Version:
1.0
|
|
Date Certified:
4/30/2018
|
|
Load Equivalency Number:
1
|
|
|
|
Voyage Recorder (VDR)
|
|
Model #:
YDVR-04
|
|
The Digital Yacht's Voyage Recorder (VDR) is intended for storing data from the NMEA 2000 network of the vessel and audio from VHF line-out or microphone amplifier on a MicroSD memory card. The software that comes with the Recorder is installing on a PC and allows GPX and CSV files to be generated with the vessel's track and extensive information about the sailing conditions, including weather, depth, engine, and even tracks of nearby vessels with AIS. That allows reconstructing of your sailings in all details. You will see your track, tracks of other vessels (with AIS) and hear VHF conversations or weather forecasts received at specific point or time.
|
|
Software Version:
1.00
|
|
Hardware Version:
1.0
|
|
Date Certified:
4/30/2018
|
|
Load Equivalency Number:
1
|
|
|
|
NMEA 0183 Gateway
|
|
Model #:
YDNG-03
|
|
Yacht Device's NMEA 0183 Gateway allows you to connect NMEA 0183 equipment to a NMEA 2000 network and vice versa. It has a bi-directional converter with wide support of message types including AIS. The configurable baud rate from 300 to 115200 baud for the NMEA 0183 port allows connection of AIS transceivers (38400 baud), fast NMEA 0183 multiplexers and PC adaptors, as well as standard NMEA 0183 equipment.
|
|
Software Version:
1.0
|
|
Hardware Version:
1.0
|
|
Date Certified:
5/1/2018
|
|
Load Equivalency Number:
1
|
|
|
|
Yacht Device Tank Adapter
|
|
Model #:
YDTA-01
|
|
Yacht Device's Tank Adaptor allows you to connect an existing resistive type fluid level sensor installed on a tank (the tank type can be configured) and get the fluid level on NMEA 2000 devices, including chart plotters and instrumental displays. It can be installed as a standalone measuring device, in parallel with an existing analog gauge (2-coil and 1-coil gauges are supported), or in parallel with a Volvo engine's MDI (Mechanical Diesel Interface) box. The Device can be used with European (10 to 180 Ohm range), American (240 to 33 Ohm range) or Japanese (0 to 310 Ohm range) standard fluid level sensors as well as with any nonstandard sensors with maximum resistance less than 400 Ohm.
|
|
Software Version:
1.00
|
|
Hardware Version:
.0
|
|
Date Certified:
7/6/2018
|
|
Load Equivalency Number:
2
|
|
|
|
Switch Control - YDSC-04
|
|
Model #:
YDSC-04
|
|
Yacht Device's Switch Control YDSC-04 allows viewing of the state and managing four channels of an NMEA 2000 switch bank from the connected buttons with LED indicators. It is designed to work in tandem with Circuit Control YDCC-04 (contains four latching relays) and compatible with other NMEA 2000 digital switching devices managed by standard NMEA 2000 PGNs 127501 and 127502.
|
|
Software Version:
1.00
|
|
Hardware Version:
1.0
|
|
Date Certified:
12/6/2018
|
|
Load Equivalency Number:
1
|
|
|
|
Circuit Control - YDCC-04
|
|
Model #:
YDCC-04
|
|
Yacht Device'sCircuit Control YDCC-04 contains four latching relays (AC and DC loads), which can be managed from connected buttons with LED indicators or over NMEA 2000 with standard PGNs 127501 and 127502. The related Switch Control YDSC-04 product is recommended for setting up additional control posts with duplicate physical buttons and state indication.
|
|
Software Version:
1.00
|
|
Hardware Version:
1.0
|
|
Date Certified:
12/6/2018
|
|
Load Equivalency Number:
3
|
|
|
|
Tank Adapter - YDTA-04
|
|
Model #:
YDTA-04
|
The Tank Adapter allows you to connect an existing resistive or voltage-output type fluid level sensor installed on a tank and display the fluid level on NMEA 2000 devices, including chart plotters and instrumental displays.
The Adapter can be configured to report one of the 15 fluid types defined in the NMEA 2000 standard, including Diesel Fuel, Gasoline Fuel, Oil, Fresh Water, Waste Water, Black Water (Sewage), or Live Well.
The Device can be used with European (10 to 180 Ohm range), American (240 to 33 Ohm range) or Japanese (0 to 310 Ohm range) standard fluid level sensors as well as with any nonstandard sensors with maximum resistance less than 400 Ohm. The Device can also be used with fluid level sensors, which output an analog voltage signal in the range of 0 to 16 Volts.
|
|
Software Version:
1.00
|
|
Hardware Version:
1.0
|
|
Date Certified:
4/9/2021
|
|
Load Equivalency Number:
2
|
|
|
|
Battery Monitor - YDBM-01
|
|
Model #:
YDBM-01
|
The Battery Monitor is primarily designed for monitoring a marine battery. However, you can use the Device with any single DC source (i.e. alternator, wind generator, etc.) or load (windlass, refrigerator, etc.). This capability increases both marine safety and sailing comfort by giving you full information about on-board DC sources and consumers.
To operate as intended, the Battery Monitor requires an appropriate external shunt, shunts in the range from 5A to 1200A are widely available. The Device should be properly wired and configured. At the minimum, you should specify drop voltage and maximum current for connected shunt. In addition, you can specify battery parameters such as nominal capacity and voltage, chemistry, etc.
Current and voltage measurement data, and, in case of batteries, calculated data (state of charge, consumed ampere-hours, battery time remaining) are output to an NMEA 2000 network and can be displayed on MFDs or instrument displays.
|
|
Software Version:
1.00
|
|
Hardware Version:
1.0
|
|
Date Certified:
4/8/2021
|
|
Load Equivalency Number:
2
|
|
|
|
|
|
|
|
|
|
